VirtualBox

Custom Query (16363 matches)

Filters
 
Or
 
  
 
Columns

Show under each result:


Results (763 - 765 of 16363)

Ticket Resolution Summary Owner Reporter
#11537 obsolete Drag and Drop to Replace File in Ubuntu Locks Up VM Matthew Starr
Description

I am running Ubuntu 12.04 with KDE as the host machine and Ubuntu 10.04 as the guest machine. When I drag a file from Dolphin in KDE on the host onto the desktop of the guest and the file being copied already exists, a problem occurs. The guest OS will popup a message asking if the file should be replaced, but the guest VM is locked up because the "Dropping Data" popup in the Host OS appears to be a modal window. When this happens the guest VM window fades its color and the Dropping Data popup sits at 99% forever. The only way to recover is to force close the entire guest VM.

I have been able to reproduce this issue multiple times. There is a period of about 3 seconds after dropping the file and before the "Dropping Data" popup where the guest OS replace file popup can be addressed, but if not pressed in that time then the guest OS locks up.

#11964 fixed Oracle Virtualbox manager has stopped working CompTech
Description

When I am installing oracle linux 6.4 x64 in a virtual machine it keeps crashing when it reboots to finish the steps to install the os. If I then restart it to do the final steps on creating the first user account it also crashes when it is about to go to the login screen for the first time. I have even tried using 4.2.14 and it does it also.

I have a hp dv6-6c35dx with 16gb ram and just changed the hard drive to a seagate hybrid drive ST1000LM014. I freshly reinstalled the windows 7 os from the factory discs and the computer is working fine. All other software is working correctly. I have attached the log files from the vm itself.

#13914 obsolete Problems with tunnel stability Conny
Description

Hallo, well I have an common USB device, which is plugged to USB0. This device has WLAN function using 802.15.4 and receives IP messages from another battery powered device. The application I use is blip from TinyOS 2.1.1. Here I use the IP-tunneling with IPv6 addresses.

The file serial_tun.conf has the following content:

#Before you run the adaptation layer and router, you must
#configure the address your router will advertise to the subnet, and
#which network interface to proxy neighbor advertisements on.

# set the debug level of the output
log INFO

#set the address of the router's 802.15.4 interface. The interface
# ID must be a 16-bit short identifier
addr fec0::64

#the router can proxy neighbor IPv6 neighbor discovery on another
# interface so that other machines on the subnet can discover hosts
# routing through this router. This specifies which interface to proxy
# the NDP on.
proxy lo #eth1

# which 802.15.4 channel to operate on. Valid choices are 11-26.
channel 23

In my VM I activate IP-tunnel over eth1. For five minutes I am able to read incoming devices and to ping the battery powered device. Suddenly, the tunnel breaks down but seams on the other hand to be there still but unable to receive anything or to be used for pinging the battery powered device. When I restart the tunnel again, everything works fine for the next 5 minutes. The application I mentioned is blip from TinyOS 2.1.1. It run before on old VM installations fine. We did not change anything at the configuration:

Host type: MAC Mavericks/ Yosemite, Windows 7/8.1, Ubuntu Guest system in VM: Ubuntu 11.04 - natty ltest VM working was 4.3.12. Also not successfull under 4.3.16

Thus, we think there might be something cased by the new version of Guest Additions.

Thanks for help, Conny

Batch Modify
Note: See TracBatchModify for help on using batch modify.
Note: See TracQuery for help on using queries.

© 2024 Oracle Support Privacy / Do Not Sell My Info Terms of Use Trademark Policy